直缝自动焊接机是自动焊接机的一种，针对直线焊缝自动化焊接的一种装备，主要应用于大型圆筒，H型钢生产，以及一些直线型设备的焊接，这种焊接一般焊接面积大，长度长，人工焊接的话，速度慢，工作量大。以下山东焊接专机为您讲解的直缝自动焊接机使用时的一些注意事项的介绍。

The straight seam automatic welding machine is a kind of automatic welding machine. It is a kind of equipment for automatic welding of straight seams. It is mainly used in the production of large cylinders, H-shaped steel and the welding of some straight-line equipment. This welding generally has a large welding area and a long length. If it is manually welded, the speed is slow and the workload is large. The following is an introduction of some precautions for the use of the straight seam automatic welding machine explained by Shandong welding machine.

直缝自动焊接专机的使用，经常会需要一些配套的设备，才能完成作业，所以要注意的是，不同的产品，需要配备不同的焊接辅助设备。

The use of the straight seam automatic welding machine often requires some supporting equipment to complete the operation. Therefore, it should be noted that different products need to be equipped with different welding auxiliary equipment.

在长度上，超过两千毫米以上的工件，一般由于设备本身或者工件的误差，可能会造成焊接缝偏移，因此就需要配置跟踪系统或者摆动系统来解决这一问题。

For workpieces with a length of more than 2000 mm, the welding seam may be offset due to the error of the equipment or workpieces. Therefore, it is necessary to configure a tracking system or a swinging system to solve this problem.

在厚度问题上，超过两毫米以上厚度的钢板焊接，焊缝的间隙就会比较大，采用工件的母材自身熔化不能填平焊缝，会有一定的焊接缺陷，需要加上自动填丝机构，来填平焊缝，才能完成高质量的焊接。

In terms of thickness, when the steel plate with a thickness of more than 2mm is welded, the gap between the welds will be relatively large. If the base metal of the workpiece melts itself, the weld cannot be filled, and there will be certain welding defects. It is necessary to add an automatic wire filling mechanism to fill the weld to complete high-quality welding.

直缝自动焊接专机使用时一定要注意以下问题，才能更好的使用。

When using the straight seam automatic welding machine, you must pay attention to the following problems to better use.

1、直缝自动焊接专机应放在通风干燥处，放置平稳。

1. The straight seam automatic welding machine shall be placed in a ventilated and dry place and placed stably.

2、检查焊接面罩应无漏光、破损。焊接人员和辅助人员均应穿戴好劳保用品。

2. Check whether the welding mask is free of light leakage and damage. Welding personnel and auxiliary personnel shall wear labor protection articles.

3、交流焊机初级、次级接线应准确无误，输入电流应符合设备要求。严禁接触初级线路带电部分。

3. The primary and secondary wiring of AC welding machine shall be accurate, and the input current shall meet the equipment requirements. Do not touch the live part of the primary line.

4、直缝自动焊接专机焊钳、电源线以及各接头部位要连接可靠、绝缘良好。不允许接线处发生过热现象，电源接线端头不得外露，应用电胶布包好。

4. The welding tongs, power lines and joints of the straight seam automatic welding machine shall be reliably connected and well insulated. Overheating is not allowed at the wiring. The power terminal shall not be exposed. It shall be wrapped with electric adhesive cloth.

5、直缝自动焊接专机与焊钳间导线长度不得超s过30米，特殊情况不得超过50米，导线有受潮、断股现象应立即更换。

5. The length of the wire between the straight seam automatic welding machine and the welding tongs shall not exceed 30m, and shall not exceed 50m under special circumstances. The wire shall be replaced immediately in case of damp and broken strand.

6、次级抽头联结铜板必须压紧，接线柱应有线圈。合闸前详细检查接点螺栓及其他元件应无松动或损坏。

6. The secondary tap connection copper plate must be pressed tightly, and the terminal should have a coil. Before closing, carefully check whether the contact bolts and other components are loose or damaged.

在设备的使用中，经常会出现一些小问题，但是如果小问题不解决的话，就有可能会造成大问题，所以说，无论是在什么样的行业，使用什么样的设备，大家都一定要注意细节，解决掉我们身边存在的一些小小的问题，可能只需要几秒钟，几分钟，就能够避免一些需要几十分钟，几个小时，几天才能解决的大问题。更多相关内容就来我们网站http://www.tayfsk.com咨询吧。

In the use of equipment, there are often some small problems, but if the small problems are not solved, it may cause big problems. Therefore, no matter what kind of industry or equipment is used, we must pay attention to the details and solve some small problems around us. It may only take a few seconds or minutes to avoid some problems that take several minutes or hours, A big problem that can only be solved in a few days. For more information, please visit our website http://www.tayfsk.com Consult.