如果您在使用数控焊接设备时遇到今天要讲的问题，可以参考后进行处理，从而延长设备的使用寿命，让其能正常使用。下面山东数控焊接设备厂家为您讲解。

If you encounter the problems to be discussed today when using the NC welding equipment, you can refer to and deal with them later, so as to extend the service life of the equipment and enable it to be used normally. Next, Shandong CNC welding equipment manufacturer will explain to you.

设备电焊工超温：

Equipment welder overtemperature:

(1)检查电级座与心肌细胞之间接地电阻可否欠佳，并形成部分短路故障。

(1) Check whether the grounding resistance between the electrical base and the myocardial cell is poor, and form partial short circuit fault.

(2)检查漏水压力，出水量和供电温度是否合适。检查水道系统是否被尘土阻塞，电级臂，电级棒和电级头因水冷却欠佳而超温。

(2) Check whether the leakage pressure, water output and power supply temperature are appropriate. Check whether the water channel system is blocked by dust, and the electric arm, electric rod and electric head are overheated due to poor water cooling.

(3)检查铜软联和电级臂，电级杆和电级头打战面可否空气氧化焦虑不安，形成打战电阻器增加发烫焦虑不安。

(3) Check whether the fighting surface of copper soft link, electric grade arm, electric grade pole and electric grade head can oxidize anxiety in the air, and form a fighting resistor to increase the burning anxiety.

(4)检查电级头的截面是否由于损坏而过多增加，进而使焊机负载并产热量。

(4) Check whether the section of the electric stage head is increased too much due to damage, which will load the welding machine and generate heat.

(5)检查焊接薄厚、负荷持续率可否超标准，使焊机负载而发烫。

(5) Check whether the welding thickness and load continuity rate exceed the standard to make the welding machine hot under load.

设备踏下脚踏板焊机不工作，指示灯没亮：

The welder does not work when the equipment steps down the foot pedal, and the indicator light does not light up:

(1)检查开关电源动作电压是否正常，自动控制系统是否正常。

(1) Check whether the switching power supply action voltage is normal and whether the automatic control system is normal.

(2)检查踏板开关接触、开关接触和分开开关电源开关是否损坏。

(2) Check whether pedal switch contact, switch contact and disconnect switch power switch are damaged.

指示灯亮，钢件卡紧不焊接：

The indicator light is on, and the steel parts are clamped and not welded:

(1)检查脚踏板的日程是否及时，脚踏开关是否灵活。

(1) Check whether the schedule of the pedal is timely and whether the pedal switch is flexible.

(2)检查数控焊接设备操纵杆的黄色螺钉是否能正确调整。

(2) Check whether the yellow screw of the control lever of the NC welding equipment can be adjusted correctly.

焊接过程中自设备不必要的溅水：

Unnecessary water splashing from equipment during welding:

(1)检查电头是否被空气氧化。

(1) Check whether the electric head is oxidized by air.

(2)检查焊接钢的腐蚀和破碎情况。

(2) Check the corrosion and breakage of welded steel.

(3)检查调整电源开关是否过高。

(3) Check whether the power switch is too high.

(4)检查电压是否太小，焊接过程是否准确。

(4) Check whether the voltage is too low and whether the welding process is accurate.

另外平时不要忘了对设备进行定期检查，从而及时发现设备问题并处理。更多相关该设备的使用事项就来我们网站http://www.tayfsk.com进行咨询吧！

In addition, don't forget to check the equipment regularly, so as to find and deal with equipment problems in time. More information about the use of this device can be found on our website http://www.tayfsk.com Consult!