Before operation, the oil stains on the upper and lower power levels should be removed. After plugging in, the oil circuit board casing should have no leakage.

运行前，先开启控制电路的转为电源开关和电焊焊接电流量小开关，调节杆数，随后开启水资源和气动阀门，再开启开关电源。

Before operation, first turn on the power switch of the control circuit and the small welding current switch, adjust the number of rods, then turn on the water resources and pneumatic valves, and then turn on the switching power supply.

管板悍机通电后，查验电器设备、实际操作组织、制冷系统、供气系统软件、人体机壳是不是有泄露。电级触碰应维持明亮和清理。若有漏水，应该马上拆换。

After powering on the tube plate compactor, check if there are any leaks in the electrical equipment, actual operation organization, refrigeration system, gas supply system software, and human body casing. Electric level contacts should be kept bright and clean. If there is a leak, it should be replaced immediately.

在运作全过程中，气体和冷却水系统软件应维持通畅。液化气应维持干躁。排水管道溫度不超过40℃，排放量可依据气体溫度调节。

During the entire operation process, the gas and cooling water system software should be maintained unobstructed. Liquefied gas should be maintained dry. The temperature of the drainage pipeline shall not exceed 40 ℃, and the discharge amount can be adjusted according to the gas temperature.

禁止在打火电源电路里加熔断丝。当负荷过小，打火管中不可以发生电孤时，控制柜的打火电源电路不可关掉。

It is prohibited to add a fuse in the ignition power circuit. When the load is too small and no arc can occur in the ignition tube, the ignition power circuit of the control cabinet cannot be turned off.

控制柜长期不应用时，应每月通电加热器三十分钟。拆换闸流管后，应加温三十分钟。控制柜在一切正常运作中加热時间不可低于五分钟。

When the control cabinet is not used for a long time, the heater should be powered on for 30 minutes every month. After replacing the thyristor, it should be heated for thirty minutes. The heating time of the control cabinet during normal operation should not be less than five minutes.

电焊焊接实际操作工作人员及相互配合工作人员务必按照规定配戴劳动者防护装备。务必采用防范措施，避免触电事故、高空坠物、一氧化碳中毒和火灾事故等事故。

The actual operation personnel and mutual cooperation personnel of electric welding must wear labor protective equipment according to regulations. It is essential to adopt safety precautions to avoid safety accidents such as electric shock accidents, falling objects, carbon monoxide poisoning, and fire accidents.

管板悍机为当场应用，设备棚应配置防水防雨、防水、防太阳，并安裝相对的安防设备。

The tube plate excavator is for on-site application, and the equipment shed should be equipped with waterproof, rainproof, waterproof, and sunscreen, and corresponding security equipment should be installed.

高处电焊焊接或激光切割时，务必注意。电焊焊接周边和下边应采用防火对策，并有的监管。

When welding or laser cutting at heights, it is important to pay attention to safety. Fire safety measures should be taken around and below the welding area, and there should be professional supervision.

焊渣时，应配戴护目镜，防止焊瘤碰撞头顶部溅出方位。

When removing welding slag, protective goggles should be worn to prevent welding overlap from splashing out from the top of the head.

下雨天室外不可电弧焊接。在湿冷地区工作中时，应立在遮盖绝缘层材料的地区，并穿绝缘鞋。

Electric arc welding is not allowed outdoors on rainy days. When working in damp and cold areas, one should stand in an area that covers the insulation layer material and wear insulated safety shoes.