焊接机械手是一种通过在工件上移动焊机来帮助焊接过程的自动化加工设备,被认为是效率较高的机械,在制焊接行业中得到广泛应用。下面来讲讲焊接机械手操作及保养规程吧。

Welding manipulator is an automatic processing equipment that helps the welding process by moving the welding machine on the workpiece. It is considered to be a highly efficient machine and is widely used in the manufacturing and welding industry. Let's talk about the safe operation and maintenance procedures of welding manipulator.

装夹工艺：

Clamping process:

（1）模具安装完毕后，将身体、头部和手离开工作台，保持距离并按下启动开关；

(1) After the mold is installed, leave the body, head and hands off the workbench, keep a safe distance and press the start switch;

（2）将所需工件有序放入工装，注意在用锤子敲打过程中工件飞出伤人；

(2) Put the required workpieces into the tooling in an orderly manner, and pay attention to the workpiece flying out and hurting people during the hammering process;

焊接完成：

Welding completion:

(1)焊接完成后，操作人员只能靠近工具转动装置的初始位置；

(1) After welding, the operator can only approach the initial position of the tool rotating device;

（2）将焊接好的工件有序、整齐地放置在料架内，不要高空放置，以免工件掉到地上伤到人员或设备；

(2) Place the welded workpiece in the material rack orderly and neatly, and do not place it at high altitude, so as to avoid the workpiece falling to the ground and injuring personnel or equipment;

(3)松开所有工装上的压紧装置，取出焊接好的工件，一定要戴好手套等用品，防止烫伤皮肤和衣服；

(3) Loosen the pressing device on all tooling, take out the welded workpiece, and be sure to wear safety supplies such as gloves to prevent scalding skin and clothes;

焊接工艺：

Welding process:

（1）焊接过程中，一定要佩戴防护眼镜，防止电弧灼伤眼睛或将物体溅入眼睛；

(1) During welding, be sure to wear protective glasses to prevent electric arc from burning eyes or splashing objects into eyes;

（2）开始焊接时，操作人员不能在机械手的工作范围内，以防翻转机械手或工装时碰伤；

(2) When starting welding, the operator shall not be within the working range of the manipulator, so as to prevent the manipulator or tooling from being bruised when overturning;

（3）焊接过程中，严禁操作人员擅自离开现场，以防突发事件造成不必要的损失；

(3) During the welding process, it is strictly forbidden for operators to leave the site without authorization to prevent unnecessary losses caused by emergencies;

山东自动焊接设备厂家提醒您，机械手工作过程中，禁止非本类人员接近机械手工作区域，禁止擅自操作机械手。日常维护程序：

Shandong automatic welding equipment manufacturer reminds you that during the working process of the manipulator, non such personnel are not allowed to approach the working area of the manipulator, and it is forbidden to operate the manipulator without authorization. Routine maintenance procedures:

(1)每班清洁一次机器人表面的灰尘、油污和杂物；

(1) Clean the dust, oil and debris on the robot surface once a shift;

(2)检查燃烧器，如有损坏或变形，更换备件并检查原点；

(2) Check the burner. If it is damaged or deformed, replace the spare parts and check the origin;

（3）检查裸露电缆的送丝管无磨损、划痕，悬吊送丝管与电缆的弹簧、橡胶绳有无脱落、松脱现象，异常处理。

(3) Check whether the wire feed pipe of the exposed cable is free of wear and scratches, and whether the spring and rubber rope of the suspended wire feed pipe and the cable are free of falling off and loosening, and deal with abnormalities.

提醒您，每班下班前，应清理各自岗位上的杂物，打扫地面，打扫工作平台，打扫设备，摆放整齐。更多相关内容就来关注我们网站http://www.tayfsk.com吧！

Remind you that before each shift leaves work, you should clean up the sundries on your posts, clean the floor, clean the working platform, clean the equipment, and place them neatly. Follow our website for more relevant content http://www.tayfsk.com Come on!